The 75-5038 Cold Air Intake is the Chevy GMC Silverado Sierra 2007.5 to 2010 6.6L LLY Duramax Diesel Cold Air Intake Kit is offered as a Closeout Special.
KLM Performance is now liquidating our entire inventory of these Products. Buy now before they're all gone!
75-5019 Cold Air Intake applications:
2007.5 to 2010 Chevy/GMC Silverado/Sierra with the 6.6L Duramax LLY
XXX Filters diesel performance intake kits are all about improving airflow to your truck's engine. The SB 75-5019 Duramax Diesel Cold Air Intake Kit with the Oiled Filter Element Flows 49.1% better than the OE Induction System while removing 99.27% of the airborne dirt at the Vehicle's Rated Flow. It's just a matter of superior design. Better airflow translates into a noticeable increase in power, acceleration and most importantly the bragging rights. These intake kits are engineered to improve the airflow to your car's engine. It starts with years of research and development, as well as the most technically advanced testing. This manufacturer tests to the ISO 5011 Air Filtration Standard in a climate controlled lab when designing and testing our intake kits. This air filtration system uses the same technology employed by Ford, Chrysler, and General Motors to develop the original induction system that comes on your vehicle.
It all starts with airflow. The more air that your engine breathes, the more oxygen it receives. More oxygen results in a better combustion. Better combustion translates into more power and better fuel economy. Clean, Cold, Dense Air is why your vehicle runs better on cold mornings than on hot afternoons as cool air is denser and contains more oxygen. You can feed your engine more oxygen by reducing the restriction of the airflow.
Thorough Research & Development
During our ISO 5011 testing, we first measure the restriction of the airflow through your vehicle's original induction system to establish a baseline. The goal of an Intake Performance Kit is to reduce the limitation of the airflow to your vehicle's engine. In layman's terms, we want to make it easier for the engine to breathe. By reducing the restriction of the airflow, your engine will have better throttle response and produce more horsepower and torque. Since your engine will not have to work as hard to produce the required amount of power the result is better fuel economy.
S&B Backs It Up: Certified Test Results
Manufacturer provides ISO 5011 Certified Test Results for its intake kits, so you can see exactly how much the airflow was improved (restriction decreased) as well as the efficiency of the filter. ISO is a worldwide federation of national standards bodies. The work of preparing International Standards is normally carried out through ISO technical committees. The particular individual International Standard utilized by this manufacturer and automotive manufacturers establishes and specifies uniform test procedures, conditions, equipment, and a performance report to permit the direct laboratory performance comparison of air cleaners, in this case, those used on internal combustion engines and compressors used in automotive and industrial applications.
These High Performance Intake Kits are engineered to maximize the amount of airflow to the engine. Exceptional design coupled with advanced research and development, allow these cold air intakes to get the power increases you demand and the protection you crave. And as with all of S&B Filters products, they are tested to the ISO 5011 Standard. High Performance Intake Kits Feature: - Washable, re-useable filter manufactured with four or eight layers of premium cotton gauze to maximize airflow and filtration. - Custom high performance air box, isolates the filter from engine heat, drawing in cooler outside air to boost engine performance. - Exceptional design streamlines airflow, allowing the engine to ingest more air, increasing horsepower. - Easy to install - CARB exempt. Each Cold Air Intake Kit S&B produces manufactured to the highest standards and submitted for CARB exemption* (*in some cases, because of engineering innovations that are brand-new, approval is still pending) - Made in the USA Better Air Flow = More Horsepower S&B's intake kits are engineered to improve the airflow to your car's engine. It starts with years of research and development, as well as the most technologically advanced testing. S&B tests to the ISO 5011 Air Filtration Standard in a climate-controlled lab when designing and testing their intake kits. This is the same technology used by Ford, Chrysler, and General Motors to create the original induction system that comes on your vehicle. Thorough Research and Development During their ISO 5011 testing, S&B first measures the restriction of the airflow through your vehicle's original induction system to establish a baseline. The goal of an Intake Performance Kit is to reduce the limitation of the airflow to your vehicle's engine to allow the motor to breath easier. By overcoming the restriction of the airflow